|
#1
|
||||
|
||||
4.10 Gears out of 2001 3/4 Ton 4x4
I just had 4.88's installed and have the stock 4.10's available for Dana 60's Front and Rear. Also, have the front carrier, as well, since the swap required a carrier change. They just turned 3000 miles. Shoot me an offer if interested.
|
#2
|
||||
|
||||
Will those gears work in a 2000 Ram is there a differance in axels?
|
#3
|
||||
|
||||
To be honest, I'm not really sure. I would think that it'd work as long as you have Dana 60's, as well, but I'm not the technically inclined one on this forum. Still in the learning stage. You may want to post a question to some of the more knowledgable one's out there. I'll see if I can find anything out in the meantime.
|
#4
|
||||
|
||||
Still have em'
Just wanted to bring the post to the front. I've still got em' if interested. I know someone out there's thinking of a gear swap to 4.10's and wants to save some cash over buying new...
|
#5
|
|||
|
|||
If I knew that they would work in my 2001 I would buy them. Did you happen to find anythign more about it?
|
#6
|
||||
|
||||
jordan12
Forgive me for the ignorance, but I remember discussing the gears with you and have lost your message. Refresh my memory... what setup do you have?
|
#7
|
|||
|
|||
I have a 2001 RAM 4x4 with a 5.9 that has the stock 3.55
|
#8
|
||||
|
||||
Jordan12...
Is it a 1500 or 2500 and do you know what Axles you have?
|
#9
|
|||
|
|||
It is a 1500. And how do I determine my axles?
|
#10
|
|||
|
|||
won't work if it's a 1500, you have a dana 44 front and chrysler corporate 9 and 1/4 rear.
|
#11
|
||||
|
||||
Thanks Rufus...
That was my gut feeling as well. I don't think that the gears will works on anything but a Dana 60, front or rear, which only comes on the 2500 or 3500 models.
|
#12
|
||||
|
||||
Bump...
Back to the top!
|
#13
|
||||
|
||||
Bump...
...and again. I can't believe that no one with a Dana 60 wants 4.10 gears...
|
#14
|
||||
|
||||
im kinda interested, but i dont think they will work. i have a 2500 but it has a dana 70 rear
|
#15
|
||||
|
||||
ajmore1
Again, I don't know for sure, but I will try to find out. What about a set for the front? Isn't that a Dana 60? I'm willing to sell a single set (1 ring and pinion) of gears if that's the case.
|
#16
|
||||
|
||||
4 THE REAR
What did you do with the Trak-Lok, did you use it with the new gears or does it go with the 4:10s?Also what about the bearings and shims? THANKS FULLPULL440
|
#17
|
||||
|
||||
fullpull440
I left the limited slip in the rear when I installed the new gears. I am selling the ring and pinion's and I also have the front carrier to sell since my gear swap required a carrier change. The bearings and shims would need to be purchased separately. I believe that when you buy the Master Installation Kits that they sell for gear sets, that includes everything you need. I did not buy these kits when I did my swap, as my truck was new enough (2001 w/ 3000 miles) that they could reuse most of my parts. Normally, an installation kit is needed for each set of gears being swapped. One kit for the front and one for the rear.
|
#18
|
||||
|
||||
Let me see what kind of money I have this week and I will get back to you. Do you by chance have a bottom price you will go, because I really only need the rear. I have 4:10s already and need to replace the rear 120k miles on them and they are starting to grunt pretty bad. THANKS FULLPULL440
|
#19
|
||||
|
||||
FullPull440...
I'm looking at $150+shipping for a set. Let me know if that is agreeable to you. Thanks!
|
#20
|
||||
|
||||
Bump!
|
#21
|
||||
|
||||
I'm interested inthem if you still have them. I'm not sure if they will fit a 2000 Dakota R/T. So i'm gonna check a couple of sites to find out but, If you know they will fit I'll get them.
Bill nplfeed@aol.com |
#22
|
|||
|
|||
nplfeed
the gears will not work on your truck... they are for a dana 60 axle on a Ram 2500-3500...
ZZ |
#23
|
|||
|
|||
Limited Slip
Don't happen to have the factory posi for that rear 60 do you?
|
#24
|
||||
|
||||
No rear posi available. I left that in when I did the gear swap. Sorry!
|
#25
|
|||
|
|||
Posi
Think of me if you go to a locker. b.mills@shaw.ca
I'll count my axle splines, mine is older. |
#26
|
||||
|
||||
Dana 60 4.10 Gears - Front and Rear
These are currently being sold on ebay!
Front set: http://cgi.ebay.com/ebaymotors/ws/eB...ADME:B:dS:MT:3 Rear set: http://cgi.ebay.com/ebaymotors/ws/eB...ADME:B:dS:MT:3 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
gears | 74 DART SWINGER | Performance Talk | 2 | 03-30-2006 11:19 PM |
good gears-bad gears | NewBlackDak | Ram Truck Chat | 13 | 09-16-2002 04:00 AM |
WTB Complete Dana 70 rear 3.08 gears, or just the gears | Thierry | Trucks - Parts Wanted | 0 | 08-31-2001 01:50 AM |
Help on gears | 98ram1500 | Ram Truck Chat | 4 | 03-02-2001 08:51 PM |
Need help with 4.10 gears! Or 3.90 gears! | SUN RA KAT | Dakota Truck Forum | 1 | 03-02-2001 05:51 PM |