|
|
#1
|
|||
|
|||
Lug Nut Torque for 2002 Ram 1500?
I just rotated the tires on the 2002 Ram 1500 QC, and I could not find the lug nut torque spec in the owners manual.
Anyone know what the torque spec is supposed to be? This has the steel rims, if that matters. |
#2
|
||||
|
||||
Lug Nut Torque
I have always used 90 ft. lbs. on all 1/2" Wheel Studs. Torque them up in stages in a star pattern and it will prevent a lot of warped rotors!
|
#3
|
|||
|
|||
Torque.........
If memory serves, it is 100-110 lb/ft. It IS in the owner's manual, just not where you would expect to find it , can't recall offhand although I remember looking awhile.
|
#4
|
|||
|
|||
for 1/2" lugs [1/2 tons]
100 ft lbs
|
#5
|
|||
|
|||
I called the Dealer, and they said 135 ft/lbs!
The 2002 Ram has wheel studs that are larger than 1/2", but I'm not sure what size they are or if they are Metric or SAE? |
#6
|
|||
|
|||
They are 9/16
|
#7
|
||||
|
||||
Good luck getting e'm off if higher than 90 ft-lb !
From my experience in general, I've always seen torque specs for lug nuts are usually recommended at somewhere around 100 ft-lbs for cars and light duty trucks.
Anything over 80-90 ft-lb is usually a major pain in the a$$ to get loose later. I always torque mine to 80 ft-lbs. (My personal preference, and I've never had a loose lug nut at that setting - ref. 1500 4x4). But I do check mine on occassion. If 80 ft-lbs seems too low to you, try 90 ft-lbs if it makes you feel safer. I hand start each lug nut, then start to snug them down gradually using a star pattern with an impact wrench set to a low to medium setting. This makes them snug enough to safely lower the tire to the ground., then hand torque each one to my spec. with a Craftsman torque wrench which snaps/clicks when the torque is reached. If you insist on following Mfr. spec., I would recommend putting a light coating of grease or anti-seize on the threads so you have a chance in heck of getting them loose the next time you need to rotate tires. This may start a big debate over whether lug threads should be dry (to prevent coming loose) vs. greased, but if you ever break off a stud because of a seized lug nut, you might decide a light coating of lubrication makes sense. Maybe they say 135 FT-LBS for bigger trucks with larger studs, but that seems rediculously tight and difficult to remove later in my opinion. Back when I first owned a car, I decided to follow the Mfr. spec of 100 ft-lbs. Even with greased threads, I had to use a breaker bar to loosen the lugnuts that had only been on for 6,000 miles, so I'm sticking with my 80-90 ft-lb policy. NTENSE99 |
#8
|
||||
|
||||
I always use 100 ft lbs with Neversieze on the studs then re-torque after 100 miles of driving.
|
#9
|
|||
|
|||
I use never-seize on the threads of the studs also, seems to work good. The factory had the studs lightly oiled.
I was not concerned about how tight the tire was as I was concerned about the brake rotors warping. I had initially installed them at 80 ft/lbs. I really should get a Factory Service Manual for the truck |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
2002 Ram 1500 RC | BombTech | Trucks - Vehicles for Sale | 2 | 05-07-2002 10:07 PM |
For all You 2002 1500 4x4 owners | medic3720 | Ram Truck Chat | 2 | 01-25-2002 03:12 PM |
2002 Ram 1500.. 4.7 or 5.9???? | pistol | Ram Truck Chat | 28 | 01-09-2002 11:17 PM |
Feedback on the 2002 Ram 1500??? | pistol | Ram Truck Chat | 2 | 12-16-2001 09:14 AM |
2002 Dodge Ram 1500 | 93dodgeshadowman | Ram Truck Chat | 13 | 03-29-2001 02:45 PM |