|
|
#1
|
|||
|
|||
Best Cam For Street 440
Im building a 440 for a Challenger that will be used almost exclusively on the street. I want it to go as fast as possible, but I dont want a terrible idle. The 440 has 9.7 to 1 compression and the car has 3.55 gears. What cam do you recommend? Comp, Hughes, Lunati, Mopar or anything el
|
#2
|
|||
|
|||
I have a similar 440 (About 9:1 compression) 4 Speed and 4.10 gears... I went with ported 906 heads and the Hughes HE3038BL cam... (230/236 duration) It idles a little rougher than stock cam but has some kick to it on the top end... I'm very pleased with the performance for a mild motor like mine....
If I had a little more compression I would have moved up to the HE3844BL, but I did want some bottom end... My .02cents... |
#3
|
|||
|
|||
I have a comp cam magnum 280 in my 440. It has a very nice idle and I run a 2500 stall with 391 gears. I love it but I drive a little at the track too.
|
#4
|
|||
|
|||
I HAVE A 9.5:1 440 + .030, TORKER II, EDEL. 750, STAGE 1 PORT MUSCLE MOTORS HEADS AND I RUN THE 292 - .509 MOPAR STICK, I RAN IT ON THE CHASSIS DYNO AT THE NATS THIS YEAR AND PULLED 351 HORSEPOWER AND 360 FT. LBS. OF TORQUE, THE CURVE IS AS FLAT AS A POOL TABLE FROM 3500 TO 5500 RPM AND IT IDLES AT 800 RPM IN DRIVE NO PROBLEM!!
|
#5
|
|||
|
|||
I agree with sublime440. The Hughes 230 is a nice cam for the street. It's strong enough without too rough of an idle or being a dog on the low end. My 440's got a Crane 312 cam and it's a bear on the street. I don't think my clutch will last more than a year if I do any decent amount of street driving with it. I've been doing some research and I've settled on replacing it with the Hughes 230. The Hughes also has a good amount of lift for it's duration since it's a chrysler cam.
BTW, I'm also going to step down from my Weiand Team G single plane manifold to the Performer RPM high rise dual plane. This combo should give me a lot more steetabillity. |
#6
|
|||
|
|||
I would use the Hughes cam also. I have not used one of their BigBlock cams yet, but everyone who has seems to love them and get better performance from them too.
|
#7
|
|||
|
|||
Thanks
Thanks for the replies!!! I have ported (by me) 906 heads, have the larger valves, and the springs are the what Hughes recomends for h3038bl because that is the one I was thinking of using. Sublime how does your car idle? Do you have power brakes and do they work with this cam? The more info the better.
Thanks Sanman |
#8
|
|||
|
|||
From Farmington... I used to ride my Dirt Bikes out there... I'm From Plymouth/New Hope area....
Car idles like a Champ at 800 RPM...Had a pretty much stock cam in there before and idle quality is pretty close.... I changed over from 516 stock heads (Came on the car, don't know why) and put on some ported 906's with 2.14/1.81 valves... Installed cam with 4 degrees advanced or 106 degree's (Centerline is 110 on those cams I believe)....Running "Hemi 4 Speed" with 8.75 rearend and 4.10 gears.... 1 5/8" Mopar Performance Headers (Kind of small I think but again came with car) .... Edelbrock Performer RPM w/ Holley 850 DP and K&N air filter...(Have 6 pack too... but it slowed the car down a bit so I tried single carb combo for racing) Car picked up a full second in 1/4 mile without second gear (Synchro is out...will pull it this winter.. car shifts fine for normal driving).... Do not have power brakes but I am betting that vacuum is there without a problem.. I talked to Dave Hughes as well and made my choice based on his suggestions... No complaints at all... Car still screams out of the hole and I dropped a tenth off my 60 ft times from the old near stock cam....My '70 Challenger has the non-stopping drum brakes.. which is always an adventure for those emergency stops... actually there not too bad. Car has run a best of 13.41 at Bandimere in Denver WITHOUT second gear... you know 1st to 3rd to 4th when racing.... That's corrected ET value of 12.49 on a 3500 LB car...at around 8.5:1 compression and no second gear... These RB motors are great! First Mopar I ever owned and I'll never go back.. The reason I bought this car in the first place is because I got my butt kicked back in High School by a 70 Challenger and I was running a 70 Firebird with a transplanted 396 Rat Motor...but that's another story...Now I have 2 cars ('72 Cuda and the '70 Challenger).... Hope you can decipher some info out of my ramblings... Good Luck... Go Vikings.. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
street help | sfr | Circle Track Chat | 2 | 07-27-2017 09:35 AM |
650 HP street car????? | 1962savoy | Performance Talk | 20 | 01-14-2009 08:11 PM |
M&H vs M/T street | eric414 | Drag Racing Forum | 4 | 06-05-2004 07:53 AM |
same as it is on the street | SUN RA KAT | Joke Forum | 0 | 02-05-2002 05:28 AM |
Street Legal,Pump gas,Street tire w/exh E.T.s | PRO | Drag Racing Forum | 19 | 10-09-2000 04:04 AM |